English language for technical colleges
in series — серия, последовательно
beyond — выше, свыше
yield point — точка текучести металла
to retain — сохранять, удерживать
to bend — гнуть
shearing — обрезка, отрезание
edge — край
to grip — схватывать
lower die — нижний штамп
upper die — верхний штамп
forming operation — операция штампования
dimension — измерение, размеры
required — необходимый
increase — увеличение
open-die forging — ковка в открытом штампе (подкладном)
hammering — ковка, колотить
within — внутри, в пределах
to enclose — заключать
rod — прут, стержень
bar — прут, брусок
involved — включенный
tolerance — допуск
upsetting — высадка, выдавливание
blow — удар
coining — чеканка
imprint — отпечаток
clamp — зажим
to hit — ударять
General understanding:
1. How can the reduction of diameter in wire drawing be achieved?
2. What is sheet metal forming and where it can be used?
3. What is close-die forging?
4. What is forging?
5. What are the types of forging?
6. What types of hammers are used now?
7. Where are coining and upsetting used?
8. What process is used in wire production?
9. Describe the process of making the roof of a car.
Exercise 2.3. Find the following word combinations in the text:
1. протягивание металла через фильеру
2. волочение проволоки
3. уменьшение диаметра
4. толщина листа
5. растягивать выше точки текучести
6. сохранить новую форму
7. края отрезаются
8. конечные размеры
9. уменьшить необходимое усилие
10. увеличить пластичность металла
11. воздушные или паровые молоты
12. сила и скорость штампования
13. внутри стенок двух штампов
14. отделочная обработка
15. малые допуски
Exercise 2.4. Translate into English:
1. При волочении проволоки диаметр отверстия волочильной доски каждый раз уменьшается.
2. Штамповка листового металла включает в себя ковку, изгиб и обрезку.
3. Небольшая деформация листа при растяжении помогает сохранить новую форму детали.
4. Изменение формы при штамповке производится путем сжатия между двумя штампами.
5. Края листа при штамповке отрезаются для получения конечных размеров.
6. При проковке деталь должна быть горячей для уменьшения необходимых усилий и увеличения пластичности металла.
7. После ковки в закрытых штампах детали не требуют большой механической обработки.
8. При чеканке деформация металла невелика и отпечаток формируется на поверхности металла.
9. Высадка используется для изготовления головок гвоздей и болтов.
Text C: «METALWORKING AND METAL PROPETIES»
An important feature of hot working is that it provides the improvement of mechanical properties of metals. Hot-working (hot-rolling or hot-forging) eliminates porosity, directionality, and segregation that are usually present in metals. Hot-worked products have better ductility and toughness than the unworked casting. During the forging of a bar, the grains of the metal become greatly elongated in the direction of flow. As a result, the toughness of the metal is greatly improved in this direction and weakened in directions transverse to the flow. Good forging makes the flow lines in the finished part oriented so as to lie in the direction of maximum stress when the part is placed in service.
The ability of a metal to resist thinning and fracture during cold-working operations plays an important role in alloy selection. In operations that involve stretching, the best alloys are those which grow stronger with strain (are strain hardening) — for example, the copper-zinc alloy, brass, used for cartridges and the aluminum-magnesium alloys in beverage cans, which exhibit greater strain hardening.
Fracture of the workpiece during forming can result from inner flaws in the metal. These flaws often consist of nonmetallic inclusions such as oxides or sulfides that are trapped in the metal during refining. Such inclusions can be avoided by proper manufacturing procedures.
The ability of different metals to undergo strain varies. The change of the shape after one forming operation is often limited by the tensile ductility of the metal. Metals such as copper and aluminum are more ductile in such operations than other metals.
Vocabulary
feature — черта, особенность
to provide — обеспечивать
improvement — улучшение
property — свойство
eliminate — ликвидировать, исключать
porosity — пористость
directional — направленный
to segregate — разделять
casting — отливка
elongated — удлиненный
to weaken — ослабевать, ослаблять
transverse — поперечный
flow — течение, поток
finished — отделанный
thinning — утончение
fracture — разрушение
strain hardening — деформационное упрочнение
brass — латунь
beverage — напиток
can — консервная банка
to exhibit — проявлять
inner — внутренний
flaws — недостатки, дефекты кристаллической решетки
inclusion — включение
trapped — зд. заключенный
refining — очищать, очистка
to avoid — избегать
to undergo — подвергаться
tensile ductility — пластичность при растяжении
General understanding:
1. What process improves the mechanical properties of metals?
2. What new properties have hot-worked products?
3. How does the forging of a bar affect the grains of the metal? What is the result of this?
4. How are the flow lines in the forged metal oriented and how does it affect the strength of the forged part?
5. What are the best strain-hardening alloys? Where can we use them?
6. What are the inner flaws in the metal?
7. Can a metal fracture because of the inner flaw?
8. What limits the change of the shape during forming operations?
Exercise 2.5. Find the following in the text:
1. важная особенность горячей обработки
2. улучшение механических свойств металла
3. необработанная отливка
4. направление максимального напряжения
5. способность сопротивляться утончению и разрушению
6. проявлять большее деформационное упрочнение
7. разрушение детали при штамповке
8. внутренние дефекты в металле
9. неметаллические включения
10. способность металлов подвергаться деформации
11. ограничивается пластичностью металла при растяжении
Exercise 2.6. Translate into English:
1. Горячая обработка металла улучшает его механические свойства и устраняет пористость и внутренние дефекты.
2. Удлинение зерен в направлении текучести при ковке значительно улучшает прочность металла в этом направлении и уменьшает его прочность в поперечном.
3. Хорошая проковка ориентирует линии текучести в направлении максимального напряжения.
4. Деформационное упрочнение металла при холодной обработке очень важно для получения металлов с улучшенными свойствами.
5. Внутренние дефекты металла — это неметаллические включения типа окислов или сульфидов.
6. Изменение формы при штамповании металлических деталей ограничивается пластичностью металла при растяжении.
FAMOUS SCIENTISTS
Mikhail Vasilyevich Lomonosov was a famous Russian writer, chemist, and astronomer who made a lot in literature and science.
Lomonosov was born on November 19, 1711, in Denisovka (now Lomonosov), near Archangelsk, and studied at the University of the Imperial Academy of Sciences in St. Petersburg. After studying in Germany at the Universities of Marburg and Freiberg, Lomonosov returned to St. Petersburg in 1745 to teach chemistry and built a teaching and research laboratory there four years later.
Lomonosov is often called the founder of Russian science. He was an innovator in many fields. As a scientist he rejected the phlogiston theory of matter commonly accepted at the time and he anticipated the kinetic theory of gases. He regarded heat as a form of motion, suggested the wave theory of light, and stated the idea of conservation of matter. Lomonosov was the first person to record the freezing of mercury and to observe the atmosphere of Venus during a solar transit.
Interested in the development of Russian education, Lomonosov helped to found Moscow State University in 1755, and in the same year wrote a grammar that reformed the Russian literary language by combining Old Church Slavonic with modern language. In 1760 he published the first history of Russia. He also revived the art of Russian mosaic and built a mosaic and colored-glass factory. Most of his achievements, however, were unknown outside Russia.
UNIT3
MATERIALS SCIENCE AND TECHNOLOGY
I. Text A: «Materials science and technology»,
Text B: «Mechanical Properties of Materials».
II. Famous people of science and technology: Igor Sikorskly, Andrey Tupolev.
Text A: «MECHANICAL PROPERTIES Of MATERIALS»
Materials Science and Technology is the study of materials and how they can be fabricated to meet the needs of modern technology. Using the laboratory techniques and knowledge of physics, chemistry, and metallurgy, scientists are finding new ways of using metals, plastics and other materials.
Engineers must know how materials respond to external forces, such as tension, compression, torsion, bending, and shear. All materials respond to these forces by elastic deformation. That is, the materials return their original size and form when the external force disappears. The materials may also have permanent deformation or they may fracture. The results of external forces are creep and fatigue.
Compression is a pressure causing a decrease in volume. When a material is subjected to a bending, shearing, or torsion (twisting) force, both tensile and compressive forces are simultaneously at work. When a metal bar is bent, one side of it is stretched and subjected to a tensional force, and the other side is compressed.
Tension is a pulling force; for example, the force in a cable holding a weight. Under tension, a material usually stretches, returning to its original length if the force does not exceed the material's elastic limit. Under larger tensions, the material does not return completely to its original condition, and under greater forces the material ruptures.
Fatigue is the growth of cracks under stress. It occurs when a mechanical part is subjected to a repeated or cyclic stress, such as vibration. Even when the maximum stress never exceeds the elastic limit, failure of the material can occur even after a short time. No deformation is seen during fatigue, but small localized cracks develop and propagate through the material until the remaining cross-sectional area cannot support the maximum stress of the cyclic force. Knowledge of tensile stress, elastic limits, and the resistance of materials to creep and fatigue are of basic importance in engineering.
Creep is a slow, permanent deformation that results from a steady force acting on a material. Materials at high temperatures usually suffer from this deformation. The gradual loosening of bolts and the deformation of components of machines and engines are all the examples of creep. In many cases the slow deformation stops because deformation eliminates the force causing the creep. Creep extended over a long time finally leads to the rupture of the material.
Vocabulary
bar— брусок, прут
completely — полностью, совершенно
compression — сжатие
creep — ползучесть
cross-sectional area — площадь поперечного сечения
cyclic stress — циклическое напряжение
decrease — уменьшение
elastic deformation — упругая деформация
elastic limit — предел упругости
exceed — превышать
external forces — внешние силы
fatigue — усталость металла
fracture — перелом, излом
loosen — ослаблять, расшатывать
permanent deformation — постоянная деформация
remaining — оставшийся
shear — срез
simultaneously — одновременно
to stretch — растягивать
technique — методы
tension — напряженность
to propagate — распространяться
to bend — гнуть, согнуть
to extend — расширять, продолжаться
to meet the needs — отвечать требованиям
to occur — происходить
to respond — отвечать реагировать
to suffer — страдать
torsion — кручение
twisting — закручивание, изгиб
volume — объем, количество
rupture — разрыв
General understanding:
1. What are the external forces causing the elastic deformation of materials? Describe those forces that change the form and size of materials.
2. What are the results of external forces?
3. What kinds of deformation are the combinations of tension and compression?
4. What is the result of tension? What happens if the elastic limit of material is exceeded under tension?
5. What do we call fatigue? When does it occur? What are the results of fatigue?
6. What do we call creep? When does this type of permanent deformation take place? What are the results of creep?
Exercise 3.1. Find the following in the text:
1. отвечать требованиям современной технологии
2. используя лабораторные методы
3. новые способы использования металлов
4. сжатие, растяжение, изгиб, кручение, срез
5. возвращать первоначальный размер и форму
6. внешняя сила
7. постоянная деформация
8. уменьшение объема
9. растягивающие и сжимающие силы
10. превышать предел упругости материала
11. повторяющиеся циклические напряжения
12. разрушение материала
13. развитие и распространение мелких трещин
14. сопротивление материалов ползучести и усталости
Exercise 3.2. Translate into English the following sentences:
1. Упругая деформация — это реакция всех материалов на внешние силы, такие, как растяжение, сжатие, скручивание, изгиб и срез.
2. Усталость и ползучесть материалов являются результатом внешних сил.
3. Внешние силы вызывают постоянную деформацию и разрушение материала.
4. Растягивающие и сжимающие силы работают одновременно, когда мы изгибаем или скручиваем материал.
5. Растяжение материала выше предела его упругости дает постоянную деформацию или разрушение.
6. Когда деталь работает долгое время под циклическими напряжениями, в ней появляются небольшие растущие трещины из-за усталости металла.
7. Ползучесть — это медленное изменение размера детали под напряжением.
Text В: «Mechanical Properties of Materials»
Density (specific weight) is the amount of mass in a unit volume. It is measured in kilograms per cubic metre. The density of water is 1000 kg/ m3 but most materials have a higher density and sink in water. Aluminium alloys, with typical densities around 2800 kg/ m3 are considerably less dense than steels, which have typical densities around 7800 kg/ m3. Density is important in any application where the material must not be heavy.
Stiffness (rigidity) is a measure of the resistance to deformation such as stretching or bending. The Young modulus is a measure of the resistance to simple stretching or compression. It is the ratio of the applied force per unit area (stress) to the fractional elastic deformation (strain). Stiffness is important when a rigid structure is to be made.
Strength is the force per unit area (stress) that a material can support without failing. The units are the same as those of Stiffness, MN/m2, but in this case the deformation is irreversible. The yield strength is the stress at which a material first deforms plastically. For a metal the yield strength may be less than the fracture strength, which is the stress at which it breaks. Many materials have a higher strength in compression than in tension.
Ductility is the ability of a material to deform without breaking. One of the great advantages of metals is their ability to be formed into the shape that is needed, such as car body parts. Materials that are not ductile are brittle. Ductile materials can absorb energy by deformation but brittle materials cannot.
Toughness is the resistance of a material to breaking when there is a crack in it. For a material of given toughness, the stress at which it will fail is inversely proportional to the square root of the size of the largest defect present. Toughness is different from strength: the toughest steels, for example, are different from the ones with highest tensile strength. Brittle materials have low toughness: glass can be broken along a chosen line by first scratching it with a diamond. Composites can be designed to have considerably greater toughness than their constituent materials. The example of a very tough composite is fiberglass that is very flexible and strong.
Creep resistance is the resistance to a gradual permanent change of shape, and it becomes especially important at higher temperatures. A successful research has been made in materials for machine parts that operate at high temperatures and under high tensile forces without gradually extending, for example the parts of plane engines.
Vocabulary
ability — способность
amount — количество
absorb — поглощать
amount — количество
application — применение
brittle — хрупкий, ломкий
car body — кузов автомобиля
constituent — компонент
crack — трещина
creep resistance — устойчивость к ползучести
definition — определение
density — плотность
ductility — ковкость, эластичность
failure — повреждение
gradual — постепенный
permanent — постоянный
rigid — жесткий
to sink — тонуть
square root — квадратный корень
stiffness — жесткость
strain — нагрузка, напряжение, деформация
strength — прочность
stress — давление, напряжение
tensile strength — прочность на разрыв
toughness — прочность, стойкость
yield strength — прочность текучести
Young modulus — модуль Юнга
General understanding:
1. What is the density of a material?
2. What are the units of density? Where low density is needed?
3. What are the densities of water, aluminium and steel?
4. A measure of what properties is stiffness? When stiffness is important?
5. What is Young modulus?
6. What is strength?
7. What is yield strength? Why fracture strength is always greater than yield strength?
8. What is ductility? Give the examples of ductile materials. Give the examples of brittle materials.
8. What is toughness?
9. What properties of steel are necessary for the manufacturing of: a) springs, b) car body parts, c) bolts and nuts, d) cutting tools?
10. Where is aluminium mostly used because of its light weight?
Exercise 3.3. Find the following words and word combinations in the text:
1. количество массы в единице объема
2. килограмм на кубический метр
3. мера сопротивления деформации
4. отношение приложенной силы на единицу площади к частичной упругой деформации
5. жесткая конструкция
6. прочность на сжатие
7. способность материала деформироваться не разрушаясь
8. поглощать энергию путем деформации
9. обратно пропорционально квадрату размера дефекта
10. постепенное изменение формы
11. повышенные температуры
12. высокие растягивающие усилия
Exercise 3.4.
Translate into