English language for technical colleges
The principal type of ignition now commonly used is the battery-and-coil system. The current from the battery flows through the coil and magnetizes the iron core. When this circuit is interrupted at the distributor points by the interrupter cam, a current is produced in the primary coil with the assistance of the condenser. This induces a high-voltage current in the secondary winding. This secondary high voltage is needed to cause the spark to jump the gap in the spark plug. The spark is directed to the proper cylinder by the distributor, which connects the secondary coil to the spark plugs in the several cylinders in their proper firing sequence. The interrupter cam and distributor are driven from the same shaft, the number of breaking points on the interrupter cam being the same as the number of cylinders.
The electrical equipment controls the starting of the engine, its ignition system, and the lighting of the car. It consists of the battery, a generator for charging it when the engine is running, a starter and the necessary wiring. Electricity also operates various automatic devices and accessories, including windscreen wipers, directional signals, heating and air conditioning, cigarette lighters, powered windows and audio equipment.
Lubrication
In the force-feed system, a pump forces the oil to the main crankshaft bearings and then through drilled holes in the crankpins. In the full-force system, oil is also forced to the connecting rod and then out to the walls of the cylinder at the piston pin.
Cooling
At the moment of explosion, the temperature within the cylinder is much higher than the melting point of cast iron. Since the explosions take place as often as 2,000 times per minute in each cylinder, the cylinder would soon become so hot that the piston, through expansion, would «freeze» in the cylinder. The cylinders are therefore provided with jackets, through which water is rapidly circulated by a small pump driven by a gear on the crankshaft or camshaft. During cold weather, the water is generally mixed with a suitable antifreeze, such as alcohol, wood alcohol, or ethylene glycol.
To keep the water from boiling away, a radiator forms part of the engine-cooling system. Radiators vary in shape and style. They all have the same function, however, of allowing the water to pass through tubing with a large area, the outer surface of which can be cooled by the atmosphere. In air cooling of engine cylinders, various means are used to give the heat an outlet and carry it off by a forced draught of air.
The Starter
The petrol engine must usually be set in motion before an explosion can take place and power can be developed; moreover, it cannot develop much power at low speeds. These difficulties have been overcome by the use of gears and clutches, which permit the engine to work at a speed higher than that of the wheels, and to work when the vehicle is at rest. An electric starter receiving its current from the storage battery, turns the crankshaft, thus starting the petrol engine. The starter motor is of a special type that operates under a heavy overload, producing high power for very short periods. In modern cars, the starter motor is automatically actuated when the ignition switch is turned on.
The Power Transmission
The engine power is delivered first to the flywheel and then to the clutch. From the clutch, which is the means of coupling the engine with the power-transmission units, the power flows through the transmission and is delivered into the rear-axle drive gears, or differential, by means of the drive shaft and universal joints. The differential delivers the power to each of the rear wheels through the rear-axle drive shafts.
The Clutch
Some type of clutch is found in every car. The clutch may be operated by means of a foot pedal, or it may be automatic or semi-automatic. The friction clutch and the fluid coupling are the two basic varieties. The friction clutch, which depends on solid contact between engine and transmission, consists of: the rear face of the flywheel; the driving plate, mounted to rotate with the flywheel; and the driven plate, between the other two. When the clutch is engaged, the driving plate presses the driven plate against the rear face of the flywheel. Engine power is then delivered through the contacting surfaces to the transmission.
Fluid coupling may be used either with or without the friction clutch. When it is the sole means of engaging the engine to the transmission, power is delivered exclusively through an oil medium without any contact of solid parts. In this type, known as a fluid drive, an engine-driven, fan-bladed disc, known as the fluid flywheel, agitates the oil with sufficient force to rotate a second disc that is connected to the transmission. As the rotation of the second disc directly depends on the amount of engine power delivered, the prime result of fluid coupling is an automatic clutch action, which greatly simplifies the requirements for gear shifting.
Manual and Automatic Transmissions
The transmission is a mechanism that changes speed and power ratios between the engine and the driving wheels. Three general types of transmission are in current use: conventional or sliding-gear, Hydra-Matic, and torque-converter systems.
The conventional transmission provides for three or four forward speeds and one reverse speed. It consists of two shafts, each with gears of varying diameters. One shaft drives the other at a preselected speed by meshing the appropriate set of gears. For reverse speed/an extra gear, known as the idler gear, is required to turn the driven shaft in the opposite direction from normal rotation. In high gear, the two shafts usually turn at the same speed. In low, second, and reverse gears, the driven shaft turns more slowly than the driving shaft. When a pair of gears permits the driven shaft to turn more rapidly than the driving shaft, the transmission is said to have overdrive. Overdrive is designed to increase the speed of a car.
The Hydra-Matic type of transmission combines the automatic clutch provided by fluid coupling with a semiautomatic transmission. A mechanical governor, controlled by the pressure exerted on the accelerator pedal, regulates gear selection through a system of hydraulically controlled shift valves. Hydra-Matic transmission provides for several forward gears.
The torque-converter type of transmission provides an unlimited number of gear ratios with no shifting of gears. The torque converter is a hydraulic mechanism using engine power to drive a pump, which impels streams of oil against the blades of a turbine. The turbine is connected to the drive shaft and causes it to rotate.
Both Hydra-Matic and torque-converter systems are controlled by a selector lever on the steering column, which provides also for reverse and sometimes for emergency-low gears.
The Running Gear
The running gear of the car includes the wheel-suspension system, the stabilizers, and the wheels and tyres. The frame of the car may be considered the integrating member of the running gear. It is attached to the rear axle and to the front wheels by springs. These springs, along with the axles, the control and support arms, and the shock absorbers, constitute the wheel-suspension system. In modern cars the front wheels are independently suspended from the frame in a manner that permits either wheel to change its plane without appreciably affecting the other. This type of front-wheel suspension is known popularly as independent suspension. The stabilizers consist of spring-steel bars, connected between the shock-absorber arms by levers, to decrease body roll and improve steerability.
The Control System
Steering is controlled by a hand wheel, mounted on an inclined column and attached to a steering tube inside the column. The other end of the tube is connected to the steering gear, which is designed to provide maximum ease of operation. Power steering, adapted for passenger cars in the early 1950s, is generally a hydraulic mechanism used as a booster to reduce the effort of steering.
A car has two sets of brakes: the hand or emergency brake and the foot brake. The emergency brake generally operates on the rear wheels only. The foot brake in modern cars is always of the four-wheel type, operating on all wheels. Hydraulic brakes on cars and hydraulic vacuum, air, or power brakes on lorries apply the braking force to the wheels with much less force on the brake pedal than is required with ordinary mechanical brakes. The wheel brakes are generally of the internally expanding type, in which a convex strip of material is forced against a concave steel brake drum.
10. TWO-STROKE AND DIESEL ENGINES
Most diesels are also four-stroke engines. The first or suction stroke draws air, but no fuel, into the combustion chamber through an intake valve. On the second or compression stroke the air is compressed to a small fraction of its former volume and is heated to approximately 440°C by this compression. At the end of the compression stroke vaporised fuel is injected into the combustion chamber and burns instantly because of the high temperature of the air in the chamber. Some diesels have auxiliary electrical ignition systems to ignite the fuel when the engine starts and until it warms up. This combustion drives the piston back on the third or power stroke of the cycle. The fourth stroke is an exhaust stroke.
The efficiency of the diesel engine is greater than that of any petrol engine and in actual engines today is slightly over 40 per cent. Diesels are in general slow-speed engines with crankshaft speeds of 100 to 750 revolutions per minute (rpm) as compared to 2,500 to 5,000 rpm for typical petrol engines. Some types of diesel, however, have speeds up to 2,000 rpm. Because diesels use compression ratios of 14 or more, they are generally more heavily built than petrol engines, but this disadvantage is counterbalanced by their greater efficiency and the fact that they can be operated on less expensive fuel.
Two-Stroke Engines
By suitable design it is possible to operate a diesel as a two-stroke or two-cycle engine with a power stroke every other stroke of the piston instead of once every four strokes. The efficiency of such engines is less than that of four-stroke engines, and therefore the power of a two-stroke engine is always less then half that of a four-stroke engine of comparable size.
The general principle of the two-stroke engine is to shorten the periods in which fuel is introduced to the combustion chamber and in which the spent gases are exhausted to a small fraction of the duration of a stroke instead of allowing each of these operations to occupy a full stroke.
In the simplest type of two-stroke engine, the valves are the openings in the cylinder wall that are uncovered by the piston at the end of its outward travel. In the two-stroke cycle the fuel mixture or air is introduced through the intake port when the piston is fully withdrawn from the cylinder. The compression stroke follows and the charge is ignited when the piston reaches the end of this stroke. The piston then moves outward on the power stroke, uncovering the exhaust port and permitting the gases to escape from the combustion chamber.
11. DIRECT-CURRENT (DC) GENERATORS
If an armature revolves between two stationary field poles, the current in the armature moves in one direction during half of each revolution and in the other direction during the other half. To produce a steady flow of unidirectional, or direct, current from such a device, it is necessary to provide a means of reversing the current flow outside the generator once during each revolution. In older machines this reversal is accomplished by means of a commutator (коллектор) — a split metal ring mounted on the shaft of the armature. The two halves of the ring are insulated from each other and serve as the terminals of the armature coil. Fixed brushes of metal or carbon are held against the commutator as it revolves, connecting the coil electrically to external wires. As the armature turns, each brush is in contact alternately with the halves of the commutator, changing position at the moment when the current in the armature coil reverses its direction. Thus there is a flow of unidirectional current in the outside circuit to which the generator is connected. DC generators are usually operated at fairly low voltages to avoid the sparking between brushes and commutator that occurs at high voltage. The highest potential commonly developed by such generators is 1500 V. In some newer machines this reversal is accomplished using power electronic devices, for example, diode rectifiers.
Modern DC generators use drum armatures that usually consist of a large number of windings set in longitudinal slits in the armature core and connected to appropriate segments of a multiple commutator. In an armature having only one loop of wire, the current produced will rise and fall depending on the part of the magnetic field through which the loop is moving. A commutator of many segments used with a drum armature always connects the external circuit to one loop of wire moving through the high-intensity area of the field, and as a result the current delivered by the armature windings is virtually constant. Fields of modern generators are usually equipped with four or more electromagnetic poles to increase the size and strength of the magnetic field. Sometimes smaller interpoles are added to compensate for distortions in the magnetic flux of the field caused